Commercial · Mesa, AZ
When a kitchen floor fails, service slows and safety risks go up. Elite Epoxy Mesa has installed and repaired commercial kitchen epoxy flooring since 2015, building seamless, easy-clean systems that stand up to grease, hot water, and daily traffic in Mesa.
Prep makes or breaks commercial kitchen epoxy flooring. We start with a site walk to identify delamination, moisture vapor, hollow spots, and failed coatings, then protect drains, thresholds, and equipment legs. Our crew uses diamond grinding (typically 30-60 grit) or shot blasting to reach clean, sound concrete, followed by HEPA vacuuming and degreasing to remove oil and surfactant residue common near cook lines and dish areas. Cracks and spalls are routed and rebuilt with epoxy mortar or polyurea crack filler, and low areas are leveled so water flows the way it should.
Mesa heat and daily washdowns can stress floors, so we match the system to your conditions and schedule. Where thermal shock is a concern, we often specify urethane cement underlayment (1/8-1/4 inch) topped with a chemical-resistant epoxy or polyaspartic wear coat; for standard prep and storage spaces, high-build 100% solids epoxy with a broadcast aggregate can be a great fit. Slip resistance is tuned with aluminum oxide, quartz sand, or a full flake broadcast depending on how wet the area gets, then sealed for cleanability. Cove base and integral toe-kicks can be added to remove grout lines at the wall and help meet routine health inspections.
Mesa kitchens choose Elite Epoxy Mesa because we plan around service hours and deliver floors that stay down. You get clear options with real specs, not vague promises, including recommended thickness, texture level, and chemical resistance for degreasers and sanitizers. We are licensed and insured, and we keep the jobsite controlled with odor management, ventilation, and dust containment so other trades can keep moving. If you need a repair instead of a full replacement, we can isolate failed sections, patch, and recoat to restore a uniform, sealed surface.
Before we wrap up, we walk the floor with you and verify slope to drains, transitions at walk-in coolers, and coverage at corners, curbs, and penetrations. You receive written care instructions (approved cleaners, scrubber pads to avoid, and recoat intervals), plus cure-time guidance so you can schedule reopening with confidence. We can add safety striping, designated dry zones, and threshold detailing to reduce slips and trip points. The result is commercial kitchen epoxy flooring built for sanitation, traction, and long service life, backed by a free written estimate and a clear install plan.
Yes. We provide a free written estimate after an on-site evaluation of the slab, prep requirements, and the coating system that fits your use.
Sometimes, but it depends on bond, thickness, and contamination. We typically diamond grind to a sound layer, remove loose material, and then recoat with the appropriate primer and build coat.
High-gloss clears can be slick with water. We can add traction media (fine polymer grit or aluminum oxide) and adjust texture to improve slip resistance without making the floor hard to clean.
For sun exposure, we commonly use UV-stable polyaspartic or aliphatic polyurethane topcoats. This helps reduce yellowing compared with epoxy-only topcoats.
Yes. We install resinous flooring for commercial and light industrial spaces and can phase work by bay or zone to reduce downtime while maintaining proper cure times.
Commercial kitchen epoxy flooring has to do more than look clean, it has to stay sanitary under grease, food acids, sanitizer chemicals, rolling carts, and nonstop foot traffic. Elite Epoxy Mesa installs and repairs seamless resin flooring systems designed for real back-of-house conditions, from cook lines and dish pits to walk-in cooler entries and prep rooms. We build floors that clean fast, resist staining, and maintain traction when wet, with system selections based on your slab condition, moisture risk, and operating schedule.
Every successful commercial kitchen epoxy flooring project starts with concrete prep and contamination control. Kitchens often have embedded oils that cause fisheyes and adhesion failures, so we mechanically profile the slab with diamond grinding or shot blasting, then deep-clean and HEPA vacuum. Cracks, joints, and spalls are repaired with compatible epoxy mortar or polyurea fillers, and we address drainage issues by correcting low spots before coatings go down. When moisture vapor is a concern, we discuss moisture-mitigation primers and realistic cure schedules.
For demanding environments, we commonly recommend urethane cement as a base because it handles impact, heat, and aggressive cleaning better than many standard coatings. For areas with lighter exposure, high-build 100% solids epoxy with a broadcast aggregate can provide a durable, economical surface. Topcoats may include epoxy, polyurethane, or polyaspartic depending on chemical exposure, scratch resistance, and return-to-service needs. Texture is customized so you get traction without making the floor hard to mop or squeegee.
If your floor is peeling, blistering, or worn smooth, repairs can often restore performance without replacing everything. We can remove failed sections, rebuild the profile, and recoat to create a uniform, sealed surface with matched slip resistance. You will receive a written scope that covers prep method, system layers, thickness targets, cove details, cure times, and cleaning recommendations. For commercial kitchen epoxy flooring in Mesa, contact Elite Epoxy Mesa to schedule a free written estimate and a straightforward plan to keep your kitchen running.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Mesa. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
